RELEASE HANDBOOKS > TRAX Version 11 > 11 - Production > 11 - Production Switches

11 - Production Switches

AUTOPAMP

When set to Yes, the information in the AMP, Revision, Date and TR fields in the A/C Type/Series, General tab will auto populate in the Work Order, Optional tab when the same tail number is associated to the Work Order.

When set to No, the information in the AMP, Revision, Date and TR fields in the A/C Type/Series, General tab will not auto populate in the Work Order, Optional tab when the same tail number is associated to the Work Order.

CCLISTCOND

When set to Yes, and the Config Other field is populated with a Condition Code, the Exchange Fee (via Exchange Order Out Detail, General tab) defaults to the value populated in the XO Exchange Fee Percent (via System Transaction Code/ General/ Condition Code) multiplied by the value populated in the Unit Sell field (via the P/N Sell, General tab).

When set to Yes, and the Config Other field is not populated with a Condition Code, the Exchange Fee defaults to the Average Cost of the part (P/N Master, Costing tab).

When set to No, regardless of whether or not the Config Other field is populated with a Condition Code, the Exchange Fee will be taken from the full amount of the Unit Sell amount. In addition, the Exchange Fee is not dependent on the XO Exchange Fee Percent established (via System Transaction Code/ General/ Condition Code).

Note: The CCLISTCOND switch also functions for Rental Orders.

Note: With the switch set to Yes or No, the user can manually override the Exchange Fee for an Exchange Order Out or the Unit Cost for a Rental Order.

DAILYEOARCHIVE

When set to Yes, Daily E/Cs and associated Task Cards that are on a Work Order with a status of 'Line' will be archived upon W/O Task Card Closing. The system will allow the user to add the E/Cs and associated Task Cards again (if applicable).

When set to No, Daily E/Cs and associate Task Cards that are on a Work Order with a status of 'Line' will not be archived upon W/O Task Card Closing.

GENRECALTWO

When set to Yes, the system will generate a Recurrent Alert Notification from a Work Order that has been associated to a defect.

When set to No, the system will not generate a Recurrent Alert Notification from a Work Order that has been associated to a defect.

LABORDATEVAL

When set to Yes, the system will not validate the W/O Manual Labor Task Card date regardless of the W/O date.

When set to No, the system will validate the W/O Manual Labor Task Card date and the user is unable to save the record if the date exceeds the W/O date.

MANDATAMP

When set to Yes, the AMP, Revision and Date fields via the Work Order Header, Optional tab will be mandatory.

When set to No, the AMP, Revision and Date fields via the Work Order Header, Optional tab will not be mandatory.

NREDITOR

The Import W/O N/R Task Card option now allows users to import Non-Routine Task Cards using the STYLESHEET Editor.

Note: This switch is not new in TRAX Version 11.

PNMANAGEDISSUE

When set to Yes, the system will not remove managed NHA Part Numbers, their P/N Controls or any NLAs and their P/N Controls associated to the NHA. The managed NHA and NLA will remain in Inventory even after the parts have been issued and the Work Order has been closed.

When set to No, the system will remove managed NHA Part Numbers, their P/N Controls or any NLAs and their P/N Controls associated to the NHA. The managed NHA and NLA will not remain in Inventory once the parts have been issued and the Work Order has been closed.

Note: The No setting of this switch only functions as described when the managed part has been issued to an aircraft that is owned by a Third Party.

PREVASKTORESET

When set to Yes, when canceling a Non-Routine Task Card, the E/C prompt 'Do you want to put E/C at Do Not Reset' will not display and the E/C linked to the Defect will automatically set to status 'RESET'.

When set to No, when canceling a Task Card, the E/C prompt 'Do you want to put E/C at Do Not Reset' will display.

WARNIFPNRESERVED

When set to Yes, users cannot delete Part requirements from a Task Card when that part requirement has dependencies (like a Picklist).

When set to No, users are allowed to delete Part requirements from a Task Card when that part requirement has dependencies.

WOACTYPEMAN

When set to Yes, the A/C Type field in the Work Order window is mandatory when an A/C is entered into the A/C field. The system will allow the user to enter an A/C that has not been entered in the system and specify an A/C Type from the A/C Type tran code list provided.

When set to No, the A/C Type field in the Work Order window is not mandatory when an A/C is entered into the A/C field. The system will not allow the user to enter an A/C that has not been entered in the system.

WOCUSTLOGO

When set to Yes, the Customer logo, saved through the Customer Master, will be used on Third Party Work Order Task Card Prints.

Note: This switch is created for stylesheet prints.

When set to No, the Customer logo, saved through the Customer Master, will not be used on Third Party Work Order Task Card Prints; and, instead, the user’s logo uploaded onto TRAX will be displayed.

WOLABOREFFEMP

When set to Yes, the W/O Man Labor Efficiencies print will filter by Employee/User.

When set to No, the W/O Labor Efficiencies will not filter by Employee.

WOLABTCOPEN

When set to Yes, Employee Manual Labor can only be applied to Task Cards that are in Open status.

When set to No, Employee Manual Labor can be applied to all Task Cards.

WOTCCLOSINGSTATS

When set to Yes, when closing a W/O Task Card the W/O status will default to a blank text.

When set to No, when closing a W/O Task Card, the W/O status will default to 'Closed'.

Note 1: This switch affects all W/O Task Card and Non-Routine Task Card windows.

Note 2: When this switch is set to Yes, it overrides Production switch TCSTCHG. For more information refer to the Production Switches Manual.

WOTPWXOAUTO

This switch enables the auto exchange order out functionality to work in conjunction with the multi-company functionality.

Note: This switch does not have Yes/No functionality.